GCPZY-100塑料高分子材料膨脹系數測試儀
GCPZY-100 plastic polymer material expansion coefficient testing apparatus
產品概述:
Product overview:
該裝置用于測試橡膠,塑料等高分子材料在一定溫差下測量長度的變化值,由此可計算其一定溫度下的平均膨脹系數,參照國標:GB1036-2006測試方法。
The device is used for test of rubber, plastic and other polymer material measuring length changes in a certain temperature difference value, which can calculate the average expansion coefficient, the temperature of the reference standard test method for: GB1036-2006.
主要技術參數:
Main technical parameters:
1 最高爐溫:室溫-1000℃。
The 1 highest temperature: room temperature -1000 ℃.
2 升溫速度,實驗過程控制參數,含PID參數。
2 the heating speed, the experimental process control parameters, including PID parameters.
⑴由智能儀表實現全過程任意調節、設置、鎖定。操作見儀表說明書。
⑴ by the intelligent instrument to realize the whole process of arbitrary regulation, setting, lock. See the manual operation instrument.
⑵提供由上位機(計算機)接口,可實現在線檢測。
The provided by the host (computer) interface, can realize online detection.
3 電源電壓:220V±10﹪,50HZ
The 3 power supply voltage: 220V ± 10%, 50HZ
4 恒溫水槽最高溫度可達100度,加熱最大功耗≤2KW
4 constant temperature water tank temperature can reach 100 degrees, the heating power ≤ 2KW
5 膨脹值測量范圍與誤差:0--5㎜±0.1%
The 5 expansion value measurement range and error: ± 0.1% 0--5 mm
6 控溫精度:±0.1℃ 溫度記錄值誤差≤±0.5﹪
Temperature control accuracy: 6 ± 0.1 ℃ temperature record value error less than ± 0.5%
7 測量膨脹值分辨率:1um
7 measuring the expansion value resolution: 1um
8.測量容積1.8升,不銹鋼真空保溫??裳b低溫液體進行低于環境溫度的線膨脹系數測試試驗。
8 measurement of the volume of 1.8 litres, stainless steel vacuum insulation. Can be installed in cryogenic liquid is lower than the environment temperature linear expansion coefficient test test.
9.測試容積溫度檢測:最小分辨:0.1℃
The 9 test volume temperature detection: the minimum resolution: 0.1 ℃
10.測試架石英管,以及石英外管,石英活塞頂桿
The 10 test frame quartz tube, quartz tube, quartz rod, piston top
11.樣品大?。鹤畲?0長*20寬*3—6厚(mm)
11 sample size: 50 maximum length *20 width *3 6 thickness (mm)
12.測試系統滿足標準:GB/T 20673-2006,GB1036-89 塑料線膨脹系數測試定方法的技術要求和精度要求。
12 test system meet the standards: GB/T 20673-2006, GB1036-89 plastic linear thermal expansion coefficient of the technical requirements of test method and the precision requirement.
13.采用石英標樣標定儀器系統
13 using quartz calibration instrument system standard sample
產品配置:
Product configuration:
測試主機一臺,
A test mainframe,
低溫水槽一臺;
Cryogenic tank a;
測試軟件一套,
A set of test software,
計算機一臺,
A computer,
標樣一個
Standard sample a